RSRP Signal Strength: Chart and Good Ranges for 4G and 5G

RSRP Signal Strength: Chart and Good Ranges for 4G and 5G

RSRP (Reference Signal Received Power) is the power your modem receives from the serving cell’s reference signals, measured in dBm. The numbers are always negative, and closer to zero means stronger. Quick answer: -80 dBm or better is excellent, -80 to -90 dBm is good, -90 to -100 dBm is fair to weak, and below -100 dBm is poor. You read 5G on the same scale, but keep in mind that RSRP tells you about coverage, not speed.

What RSRP measures

The Teltonika Networks Wiki calls RSRP and RSRQ the key measures of signal level and quality for modern LTE networks. It defines RSRP as “Reference Signal Received Power” and describes it as an RSSI type of measurement.

In plain terms, every LTE cell sends out small, known reference signals spread across its channel. Your modem listens for those specific signals from the cell it’s connected to and reports how much power reaches it. That figure is your RSRP.

Why the numbers are negative

dBm means decibels relative to one milliwatt. Cellular signals arriving at your antenna are a tiny fraction of a milliwatt, so they come out as negative numbers. The closer to zero, the stronger the signal. So -85 dBm is a much stronger signal than -105 dBm, even though 105 looks like the bigger number.

The scale is logarithmic, which means small changes in the number are big changes in actual power. A 10 dB difference is a factor of ten. Moving from -105 dBm to -95 dBm isn’t a small tweak: it’s ten times the received power.

RSRP vs RSSI

RSSI (Received Signal Strength Indicator) is the total power your modem hears across the whole channel. That includes your serving cell, but also neighboring cells, interference and background noise. A high RSSI can look great on paper while the cell you actually care about is buried in other signals.

RSRP filters all that out and looks only at the serving cell’s reference signal. That’s why routers use RSRP, not RSSI, to judge LTE and 5G coverage.

RSRP signal strength chart

These bands come from two manufacturer references: the Teltonika Networks Wiki and Ubiquiti’s help article on cellular signal. They agree on the numbers and differ slightly on one label.

Rating RSRP (dBm) What to expect
Excellent -80 or better Strong, stable signal with plenty of headroom
Good -80 to -90 Reliable connection for most business and home use
Fair to poor (Teltonika) / Weak (Ubiquiti) -90 to -100 Usable, but more prone to slowdowns and drops
Poor Below -100 Unreliable, expect disconnects

Teltonika rates -80 dBm and up as “Excellent,” -80 to -90 dBm as “Good,” and -90 to -100 dBm as “Fair to poor.” Ubiquiti lists the same first two bands for LTE signal health, calls -100 to -90 dBm “Weak,” and labels anything under -100 dBm “Poor.”

Treat these as rules of thumb, not hard cutoffs. The same reading can behave differently depending on the modem, the band, your antenna setup and how busy the tower is.

RSRP on 5G: what changes

5G NR reports a comparable value, usually labeled SS-RSRP or NR RSRP. Instead of LTE’s cell reference signals, it’s measured on the synchronization signal block (SSB) that 5G cells broadcast. It uses the same dBm scale, and many router dashboards simply apply LTE-style color bands to it.

A few things are worth knowing:

  • Non-standalone 5G shows two readings. Most 5G today runs in non-standalone mode, which uses an LTE “anchor” connection for control. Your router may show an LTE RSRP and a separate 5G NR RSRP. Both matter: if the LTE anchor gets weak, the 5G leg can drop even when the NR reading looks fine.
  • Frequency changes the picture. Higher-frequency bands lose strength faster with distance and through walls. A reading that’s perfectly usable on a low band can fall apart quickly on a mid or high band if you move a few meters or close a door.
  • There’s no separate universal 5G chart. The references above publish their bands for LTE. Using the same bands for 5G is a reasonable starting point, but don’t expect a standard set of 5G-specific thresholds across vendors.

What your reading means in practice

  • Excellent and good (-90 dBm or better): This is where you want a primary or failover connection. VoIP, video calls, VPN tunnels and automatic failover should behave predictably, assuming signal quality (more on that below) is also decent.
  • Fair to weak (-90 to -100 dBm): It works, but you’ll likely notice slowdowns at busy times and the odd drop. This is the band where testing an external antenna usually pays off.
  • Poor (below -100 dBm): Expect disconnects. Treat it as a signal problem to fix before you blame the router, the SIM or the carrier.

Location matters a lot. Readings indoors are almost always worse than outdoors, and basements, concrete buildings and low-E glass can cost you a full band or more. Rural sites often depend on a single distant tower, so readings tend to be lower but steadier. In cities you’ll usually see stronger RSRP, but busier cells and more interference.

Here’s a hypothetical that comes up all the time: a router installed in a metal network cabinet in a back room reads in the weak band, somewhere around -98 dBm, and the failover link keeps dropping. The cabinet is acting as a shield. Run a cable to an antenna mounted on the roof, with a clear view toward the tower, and that same site can move up into the good or excellent band without touching the router at all.

RSRP vs RSRQ and SINR: why strength isn’t speed

RSRP is only one of three numbers you should look at together:

  • RSRP: coverage. How strong is the serving cell where you are?
  • RSRQ (Reference Signal Received Quality): quality, affected by cell load and interference.
  • SINR (Signal to Interference plus Noise Ratio): how much your signal stands out from interference and noise.

They’re linked. Teltonika notes that a modem needs a minimum of -20 dB SINR on the sync channel just to detect RSRP and RSRQ at all. If the noise is too high, the modem can’t even measure the signal properly.

The most common confusing pattern is good RSRP with poor SINR or RSRQ. The signal is loud, but something is drowning it out. Usual suspects are interference from another cell, a congested tower, or sitting where two sectors overlap. Pushing RSRP higher won’t fix that. A directional antenna aimed at one cell, locking to a different band, or connecting to a less busy tower often will.

So don’t chase RSRP alone. A setup at -88 dBm with clean SINR will usually beat one at -75 dBm with lots of interference.

How to check your RSRP

Most cellular routers show RSRP on the cellular, WAN or modem status page of their web dashboard. That includes Peplink, Digi, Teltonika and Semtech (formerly Sierra Wireless) devices. Menu names and paths change between models and firmware versions, so look for a page with signal details listing RSRP, RSRQ, SINR, band and cell ID.

For a Digi example, 5Gstore’s YouTube tutorial “Digi – How to Check & Interpret the Cellular Signal” walks through where the readings are and how to read them.

Phones can show RSRP too, usually through a hidden field-test or engineering mode. How you get there depends on the phone and OS version, and a phone’s internal antenna won’t match what a router with external antennas sees. It’s still handy for a quick survey of a site before you install anything.

Tips for a reliable RSRP signal strength test

  1. Test from the exact spot and height where the router or antenna will live.
  2. Give each position a few minutes. Readings bounce around, so note the typical value, not the best one you saw.
  3. Repeat at different times of day. Busy hours can change RSRQ and SINR a lot, and sometimes RSRP too.
  4. Write down the band and cell ID with every reading, so you know you’re comparing the same tower.
  5. If your router allows band locking, lock the band while you compare antenna positions. Otherwise the modem may hop bands mid-test and muddy your results.

How to improve RSRP

Work through these in order, from free fixes to hardware:

  1. Move it up and out. Put the router or antenna higher, near a window facing the tower, and away from metal, cabinets and enclosures. This alone can move you a whole band.
  2. Add an external antenna. An omnidirectional antenna picks up signal from all around, which suits vehicles and sites with several towers nearby. A directional antenna focuses on one direction, which is better for reaching a single distant tower and can also help with interference.
  3. Use MIMO properly. Connect an antenna lead to every cellular port on the modem, and use cross-polarized MIMO antennas or correctly oriented elements. Leaving ports empty or mismatching polarization throws away performance.
  4. Keep cables short and low-loss. Every meter of coax loses some signal, and thin or long cable runs can cancel out all the gain of a good antenna. Use the shortest run you can, low-loss cable, and the right connectors without unnecessary adapters.
  5. Consider a signal booster where it fits. Boosters can help when there’s usable signal outside but very little inside, especially for phones and multiple devices.
  6. Re-test after every change. Compare RSRP together with SINR and RSRQ. If RSRP rises but SINR drops, you may have pointed at a noisier cell.

If you need the hardware, 5Gstore sells antennas, cables and signal boosters, and has a router comparison tool and a connector/cable reference to help you match parts. Its US-based support team, with engineer-certified staff, can be reached by phone if you’d like a second opinion on your readings before buying anything.

Your next step: pull up your router’s signal page, note RSRP, SINR and band at your current spot, then try the first fix on the list and compare.

Sources

Michael Ginsberg, founder of 5Gstore.com

About the Author

Michael Ginsberg is the founder of 5Gstore.com, a trusted source for cellular routers and failover networking solutions since 2005. With a background in software and networking dating back to 1988, he writes about cellular connectivity, IoT infrastructure, network security, and fleet management. Connect with Michael on LinkedIn or reach the 5Gstore team through our contact page.