5Gstore Remote Power Switch - 2 Outlets (Type I Plug for Australia, New Zealand, Argentina, China)

Yes, you can download ezDevice for Android or iOS devices.

Yes, Surge protection can be used with the IP switch.

The Remote Power IP Switch is only able to ping to IP address, not Ports.

You would lose access to the remote device if this was the case. By changing the mode to reset only, you can avoid this issue so you can only issue reset commands, not separate off/on commands.

You can upgrade while deployed, however this will cause the connected devices to power cycle while the upgrade completes. Ideally doing your upgrade during off hour times is the best option.

Yes, you can do this by using the manufacturer's cloud service - cloud4UIS.com. There is also a mobile app called ezDevice, which is available for iOS and Android.

0 degrees C to 60 degrees C (32*F ~ 140*F) at 10% ~ 90% relative humidity.

Yes, the 5Gtore Remote Power IP switches support a schedule feature.

5Gstore has a support document available on our support portal called "How to Access IP Switch from Cloud Service" that you can reference for instructions.

You can schedule outlets to turn on and off or reset, which means they will be turned off and then back on. The time it waits after turning the outlet off before it's turned back on is configured on the Configuration page. Refer to the "Power On Delay for Outlets 1 & 2" as this is what will be followed when you set a schedule for Reset. Times can be configured between 1 and 600 seconds.

The default configuration values are perfect for a typical home setup. Having an aggressive value will help with keeping the internet offline for the shortest time frame.

Yes, the hostname of the device can be changed.

Input: 125~250V~50/60Hz

The Remote Power IP switch is meant to perform an automatic reboot of your router/modem (or other device) when an internet connection is lost. Of course when units are on battery backup, they are unable to power reset as needed. So, when you have a UPS in place, you need to setup in this order: UPS -> IP Switch power supply -> Modem / Router plugged into the 2 outlets - this will allow the switch to cut power properly while still maintaining battery backup for the Switch itself.

The IP switch will reset once the Internet becomes active again after an extended internet outage. How many times it resets will depend upon how you configure the setting that controls how many resets it will perform when Internet outage is detected.

The dual outlet IP switch supports a max 10 minute delay between outlet 1 and outlet 2 during reset.

Yes, the Switch has a replaceable fuse. Refer to our support document called "Remote Power Switch - Changing the Fuse" for instructions on how to do this.

Yes, you can configure a static address.

No it does not. It does come with a removable fuse and a backup though. In the event the 5A (dual outlet) or 10A (single outlet) power it supports is exceeded, it will blow the fuse. We would still recommend having a surge protector in place to protect your device(s) from any damage.

No. The 2 outlet Remote Power IP Switch however does allow for control via HTTP or XML.

Yes, this is possible. Refer to the user manual under Configuration -> Schedule for instructions OR contact our support team for assistance.

The dual outlet switch supports DDNS settings, OR you can use the manufacturer's cloud service, Cloud4UIS, for remote access to any models.

The 1 Outlet Remote Power Switch would not be able to set a delay between 2 devices as it only has 1 outlet. Our 2 Outlet Remote Power Switch would be appropriate in this case. The delay you can set between outlet 1 (where you would attach your modem) and outlet 2 (where you would attach your router) is 1 to 600 seconds.

Yes! The outlet ping targets are configurable and you can set targets to reboot just one outlet, or both, depending on your preference.

Yes, but you will need to configure a static IP address on the switch in order to access it from the computer. You can either do this by connecting the IP Switch to a router first OR if you have a Windows computer, you would connect it directly to that and use the Utility program to assign it an IP address. Our support team can assist you with this if needed.

No API is available, but there is a way to do this via HTTP commands. Contact our support for more details (support@5gstore.com).

If just rebooting the router resolves this issue for you, the single outlet model should be all you need. If you need to reboot both the modem and router, and even the security system, go with the Dual Outlet model. Both models can be accessed via iOS/Android app called ezDevice.

This depends on how many amps the PC draws. The dual outlet switch can handle 5A per outlet.

The single and dual outlet IP Switches can have power strips attached as long as you do not exceed the 10amp output (5A per outlet on the dual model).

See here: http://5gstore.com/ipswitchupdates

Yes, you have the option to turn the auto-reset function on or off..

If the IP Switch has a full power outage, when power is restored it will restore the same way it was turned off. Outlets that were off or on, will come back that way when power is restored to the switch. The switch will then go into its behavior as its set, to either start pinging for auto reset, or to delay for the amount of time you set. With the latest firmware there is also a setting you can enable to force a reset to the outlets upon initial power up. This way, in case the equipment is still not responsive, it immediately power cycles the outlets.

You can use this to cut and provide power to the PC's power supply. However, if your PC requires you to press a power button to turn it on, this won't help there. You'll need to check your PC BIOS settings to see if it can automatically turn on when it has power.

In the current firmware with default configuration, the switch will attempt 1 reset, per the duration set within the device. After this reset, it will wait for the connection to return since the power cycling clearly is not working. Once the connection is back, the switch resume normal operation. If necessary, the resets can be configured up to 30 times.

Yes, you can use the schedule feature to configure this.

There is a standard 1-year manufacturer's warranty that covers defects and failures not related to misuse/abuse. You will need to contact 5Gstore support (833-547-8673 x3 or support@5gstore.com) for a replacement. Shipping fees are not included.

No they do not.

No. It is FCC and CE certified and has been tested to be compliant with FCC 47 CFR Part 2 and Part 15 Class B equipment regulations.