Please Wait...

Cel-Fi GO G32 Smart Signal Booster Kit - RV/Trucker Antennas - DISCONTINUED

No Longer Available

Item Number: 11598



This product is end of life, recommended product(s) are:
  • Coverage area*: up to 15,000 square feet
  • Includes a 23" Trucker antenna w/ Spring Base and 1x Mobile Server Antenna
  • Compatibility: This amplifier can be set to AT&T (3G/4G/LTE), T-Mobile (3G/4G/LTE), or Verizon (LTE only) - you must choose one, it will NOT boost all three at the same time.
    • Verizon users: this amplifier will not help with Verizon 3G, and it will only help with voice/calling if you have HD Voice/VoLTE enabled on your phone and are in an LTE area. Read more about enabling HD Voice/VoLTE
  • 3G / 4G / LTE Voice and Data
  • Superior Performance: 100dB Max Gain
  • Multi-User Mobile Coverage
  • Multi-Carrier Support with Carrier Switching
  • Indoor / Outdoor NEMA 4 Rated
  • Network Safe
  • Cel-Fi WAVE management platform

Cel‐Fi GO G32 uses Nextivity’s award-winning, network-safe Cel-Fi Smart Signal Booster technology to dramatically improve voice and data coverage in up to two (2) bands for 5G(does not support Ultra Wide band 5G)/4G/3G. It is designed to improve indoor and outdoor cellular coverage when one bar is available outdoors, by allowing an antenna to be used to improve indoor cellular performance. In addition to being cost effective and easy to install, Cel-Fi GO can easily optimized and monitored through the Cel-Fi WAVE platform.

*Many factors will influence the actual coverage area you will see from a repeater, including layout/floorplan, construction, and original un-amplified signal strength. Depending on your situation, you may see more or less coverage than the estimates listed here. It is not possible to guarantee coverage area.

Installation notes:

  • In order for your system to function properly, you must maintain adequate separation between the outside and inside antennas (if the antennas are too close together, there will be oscillation/feedback between the antennas and the amplifier will power down). This amplifier requires up to 50' of separation between the outside and inside antennas. Separation can be horizontal or vertical.
  • If you cannot achieve adequate separation to eliminate oscillation, the gain on the amplifier will automatically adjust, but that will result in a smaller coverage area from the amplifier.
  • Make sure the inside antenna is aimed AWAY from the outside antenna if possible.

Features & Benefits:

  • 3G & 4G / LTE support (WCDMA / HSPA+ / LTE)
  • Supports two (2) bands simultaneously from a single operator
  • Up to 100dB system gain, per band
  • Peaceful coexistence with adjacent Wi-Fi (2.4 GHz & 5 GHz), femtocells, and cellular devices
  • Advanced digital echo-cancellation (>30dB) and channel select filtering algorithms
  • Automatic Gain Control (AGC) based on fast real-time echo-cancellation
  • NEMA 4 rated enclosure and connectors
  • Glanceable LED User Interface (UI)
  • Supporting smart phone application (WAVE)
  • Convection cooled cast aluminum chassis
  • Easy mounting capability (mounting screws and anchors included)
  • Systems are pre-configured for a single carrier (network operator)
  • Works with any user equipment (UE) on the configured network (no whitelist/blacklist)
  • System intelligence accurately establishes proper safe uplink power in real time
  • Uplink Muting Mode automatically shuts down uplink cellular transmissions when no active user equipment is detected
  • System shuts down upon Operator’s network command or failure detection
  • Nextivity purpose-built, high-performance, six core ASIC processor, provides best performance at lowest cost

Package Includes:

  • Amplifier
  • Power supply
  • 23" Trucker  antenna
  • Mobile Server antenna
  • Mounting screws and anchors


  • Compliance:
    • 3GPP TS 25.143 Rel.10
    • 3GPP TS 36.143 Rel.10
    • FCC Part 15, 20, 22, 24, 27
    • Bluetooth BQB
    • CE
  • System Management (Software):
    • Supported by WAVE cloud portal
    • WAVE Portal capability:
      • Status (List and Map)
      • Settings
      • Commissioning
      • Reporting
      • Diagnostics
      • Alarms & Notifications
      • Software Updates
  • Antenna Ports (donor & server):
    • 729 – 2155 Mhz
    • Impedance: 50 Ohm
    • Return Loss: 8 dB
    • Output Protection
    • SMA female
  • Environmental:
    • Operating temperature: 0° to 65° C
    • Convection Cooling
    • Relative humidity: 0% to 95%, noncondensing
    • WEEE
    • NEMA 4
    • Surface Temp at any point (30° ambient): 53° C
  • Dimensions:
    • 1.71" x 3.8" x 10.73"  (43.5mm x 96.5mm x 272.5mm)
    • 1.87lb (850g)
  • Power:
    • 9.6 – 16.5V
    • 2A current draw
    • 16W nominal power consumption
  • Installation:
    • Mounting hardware included
  • AC Power
  • Radio Performance:
    • The GO G32 system can boost up to two (2) bands concurrently. Either profile can be selected:
      • A) One (1) High band boost and one (1) low band boost or
      • B) Two (2) high bands boost
  • Bands Supported:
    • Band 2:
      • Downlink: 1930-1990 MHz
      • Uplink: 1850-1910 MHz
      • MHz: Up to 20MHz contiguous boost, HSPA or LTE
    • Band 4:
      • Downlink: 2110-2155 MHz
      • Uplink: 1710-1755 MHz
      • MHz: Up to 20MHz contiguous boost, HSPA or LTE
    • Band 5:
      • Downlink: 869-894MHz
      • Uplink: 824-849 MHz
      • MHz: Up to 15MHz contiguous boost, HSPA or LTE
    • Band 12:
      • Downlink: 729-746 MHz
      • Uplink: 699-716 MHz
      • MHz: Up to 10MHz contiguous boost, LTE
    • Band 13:
      • Downlink: 746-756 MHz
      • Uplink: 777-787 MHz
      • MHz: Up to 10MHz contiguous boost, LTE

This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider.
You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person.
You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider.
WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.
Please note, the four largest carriers - AT&T, T-Mobile, Verizon and Sprint - and more than 90 regional carriers have given blanket consent for use of all boosters certified to the new FCC standards.

Filter Reviews
   Last 2 Weeks (0)   
    40% (2)
    40% (2)
    20% (1)
    0% (0)
    0% (0)
  Show Brief Review
  Show 5Gstore Comments
 Last 6 Months (0) 
All Reviews (5)

Only customers who bought this item from 5Gstore can write a review - these are all verified 5Gstore purchases

Date Added: 10/29/2020 by alexander o. (Jacksonville, FL)
I can now make phone calls inside that are at least as good as when I'm outside. I guess I was hoping to have a better signal than outside with this booster, but at the end of the day, I'm able to make phone calls from inside! Heck, I'm even able to use my cell phone as a hot spot when my satellite internet is out (frequently).

In all fairness, I'm in an area where the signal seems to roam around. When you have two bars in one spot, given a little bit of time, there's no signal and you get 2 bars 25 feet away. It's definitely worth getting!

Date Added: 03/27/2019 by Ken S. (Palacios, TX)
I bought this to used while camping in our RV in the Colorado mountains this summer. To date, I've only temporarily set it up at my house (where there is a relatively strong cell signal) to verify it works (which it did). So I cannot comment on the product beyond that.

5Gstore Comments:
This review is for a previous version of this product - comments about specific features, problems, or functionality may not apply to the current model.

Date Added: 03/11/2019 by Thomas S. (Marengo, IL)
This is quite a good device. Without this amplifier and yagi attenna, my RSRP is -122 dB which is barely 1 bar. After the installation, configuring the amplifier for Verizon, and proper pointing of the antenna, I am now at a solid 4 bars and -74 dB with a SNR of 5-10. I live in a heavily wooded area 2-3 miles from the nearest cell tower. I am in fact, in between 2 cell towers - 1 to my northwest and 1 to my southeast.

The setup I purchased is the booster, yagi antenna, interior antenna, 100' of low loss cable between the booster and the yagi antenna and 30' low loss cable between the booster and the inside antenna. This configuration replaced a SureCall Fusion4home which was pretty good. This is better by 10 - 20%.

The folks at the 5Gstore are amazing as well. Thank You very much and may God bless each of you.

5Gstore Comments:
This review is for a previous version of this product - comments about specific features, problems, or functionality may not apply to the current model.

Date Added: 12/10/2018 by Sheila. (Miami, FL)
Appears to be working ok, took a 1-2 bar signal to 2-3 bars.

5Gstore Comments:
This review is for a previous version of this product - comments about specific features, problems, or functionality may not apply to the current model.

Date Added: 10/19/2017 by JAMES S. (Delta Junction, AK)
The Cel-Fi GO X Booster is an outstanding solution for difficult sites. Up here in remote Alaska my cabin is in a hole with the nearest cell tower a little over 20 miles away. My site survey did not produce a workable signal until I was up a 24 foot extension ladder against a spruce tree, on top of a nearby hill, over 400 feet from the cabin. I spoke with lots of folks from different companies but it was Valerie on the 3G Store team and her “can do” attitude that told me about the Cel-Fi GO X. Valerie and I had extensive technical conversations. The “ace up the sleeve” on this booster is the 100 dB boost which is 30 dB over what anyone else can do because of Cel-Fi agreements with ATT and Verizon. In my case the best I could do after extensive site preparation, which included clearing a “sight line” from the top of the hill through the forest towards the cell tower was -112 dB (fairly solid 1 bar) at the top of the ladder, but still over 400 feet from the cabin! Valerie pulled together my order with the Cel-Fi Yagi, 50 ft of LMR400 coax to the Cel-Fi GO X Booster, 450 feet of custom LMR 400 coax to the cabin and the Cel-Fi Panel antenna for inside.
The booster is now mounted up the hill in a small outbuilding I placed at the base of the spruce to keep the coax run between the antenna and booster as short as possible. I ascended the spruce and “topped” it when the diameter of the tree got to about 3 ˝ inches. Next, I bolted on a 13 foot pole to which I mounted the Cel-Fi Yagi which ended up about 50 feet above ground. One of the neat things about this booster is the “Wave” application that allows you to check various performance measures and settings via “blue tooth”. When I energized the system I could now check measurements of signal strength at the point it enters the booster BEFORE amplification. With the gain of the Yagi itself and the fact that the height of the Yagi was higher than I could ever physically get I am now getting -93 dB going INTO the Booster. The big unknown was how the amp was going to perform down a 450 foot LMR 400 coax run to the cabin.
BOTTOM LINE – I now get -81dB (5 bars!) of LTE inside the cabin six feet in front of the panel antenna! Remember, there was NO SIGNAL inside, outside or even on the roof of my cabin. This pulled our cabin right out of the stone age and now we are able to stream multiple TV sets, internet and phone calls all at the same time. We live off the grid and I am able to power the GO X Booster up the hill from the cabin via a dedicated inverter off my 12 volt battery bank running 110v power up a 10 gauge cable which runs along side the coax coming down the hill. We were pushing hard to finish this project before the “freeze-up” which is occurring as I write this (mid October). Everything is now covered in snow that will not melt until April.
Our extreme temperatures are, of course, a concern for the “operating temperature” of the booster. Once again the “Wave” application allows me to check the internal temperature of the booster which creates enough heat to protect itself quite a bit. I could see that at an outside temperature below freezing in the upper 20's F the internal temp of the booster was still above 70 F. To address our super cold of subzero down to -30F to -40F I built an insulated box which dramatically harvests and recycles the heat with initial tests showing an 80F difference between amp temps & outside temps so I am optimistic the setup will work well through the super cold. The “Wave” application allows me to hike up to what we are now calling “LTE Hill” in the snow and check the temperature of the booster without disturbing the insulted box or even entering the outbuilding.
If you have a tough site take heart from my experience and consider the Cel-Fi GO X! This booster changes the definition of what is possible when you perform your site survey.

5Gstore Comments:
This review is for a previous version of this product - comments about specific features, problems, or functionality may not apply to the current model.

If you purchased this item, Login to write a review.
Q & A
Got questions about this product? Here you can view questions that other customers have asked (and the answers!). If you have a question that hasn't been answered below, you may submit a new question and 5Gstore will answer it!

Click here to submit a new question