Pepwave MAX BR1 Mini with Cat 4 LTE Modem + Primecare (HW3)

Yes, the LAN ports work without the feature pack license. The WAN port and Wifi as WAN option is unlocked permanently via the feature pack. However, Peplink allows those features to work for free as long as the BR1 Mini is updated to 8.4.1 firmware or later and has an active PrimeCare warranty.

If you have an active Primecare warranty and you are on firmware 8.3.0 or higher the feature pack is not required for those features. If you plan to not renew your Primecare warranty then the feature pack will be necessary to keep those features active.

Yes, they can be found on the Peplink Forums

Yes, Peplink offers QoS controls and multiple ways to adjust bandwidth usage, as well as monitor usage.

No, it is included with it now, but you don't have to renew the PrimeCare if you don't want to.

The Peplink MAX BR1 Mini HW3 CPU is 32bit.

10 - 15 seconds is recommended.

Yes, you could create a separate LAN for the secondary WiFi SSID, create a User Group QoS Rule that would assign that new LAN as Group "Guest", and then set the Bandwidth Control for the Guest group to the desired percentage.

The Peplink MAX BR1 Mini supports 2x 4FF (nano) SIM card slots. They can be used one at a time, in a failover/ backup fashion.

No, they can only be used in a failover fashion. meaning only one will connect at a time. You need a unit with two or more modem modules in it (eg. BR2 Pro) in order to have 2 SIMs connected simultaneously.

No, this is a full functioning cellular router. It is much like a router you would use at home but with a cellular modem in it as the internet connection.

Yes, with firmware version 8.1.0 and higher.

This model has 2 redundant SIM slots so it can connect to whichever SIM you list as the preferred, otherwise it defaults to SIM A first. This is the ONLY WAN connection that can failover based on signal. There is a section called "Signal Threshold Settings" and if the signal does not meet your threshold, it automatically disconnects and tries the next SIM.

Yes, as this will only connect to a cellular network for Internet access out of the box. If another WAN source (ethernet or WiFi) is needed, the feature pack can be added to support those connections and then a SIM card would NOT be needed.

The Peplink MAX BR1 Mini Cat 4 is compatible with all major US carriers.

Yes, see here: https://5gstore.com/product/10233_peplink_gpio_cable_for_max_br1_pro_5gltea_classic_minihw3_transit_minicorepropro_e_br2_pro.html

See here for details about Primecare: https://www.peplink.com/support/peplink-primecare/ Even if you do not utilize the SpeedFusion/ FusionHub and InControl2 benefits, this still serves as the hardware warranty on the device.

There are 2 ports labeled LAN and 1 port labeled WAN. All three work as LAN ports unless you purchase the feature package that enables the LAN/WAN port to be used for WAN.

No - this router has a single modem with redundant SIM slots. This means you can have two SIMs inserted, but only one will be active at a time. The second SIM can be used for backup, failover, etc (e.g. you can configure the router to prioritize one SIM and switch to the second one only if the first is unavailable, or to switch when a certain data cap is reached, or to switch if the signal is poor, etc)

Dual yagi setups are recommended and typically installed as shown here: https://i.ytimg.com/vi/ogO6uGr5wJw/hqdefault.jpg

This does NOT support Bridge mode for WiFi WAN or any WAN connection.

It can, but you will need to check with your service provider first to confirm if they can activate the device in their system. You will also need to confirm the cellular frequency bands your service provider uses to ensure it will operate properly on their network.

It will cover about 150-200ft through walls, much greater unobstructed (variable depending on interference from other electronics and physical interference such as walls and ceilings)

The Pepwave MAX BR1 Mini HW2 and HW3 are rated between -40° - 149°F.

Yes, cellular, WiFi, and GPS antennas are included.

Aside from InControl 2, there are 3 other ways to view GOS data - via the web admin page, downloading GPX files, or by exporting the data. See more on this Peplink knowledgebase article: https://forum.peplink.com/t/accessing-gps-info-from-pepwave-max-routers/8262

It may, but the cellular provider might not allow it. We suggest checking with them first.

Yes, this will work with the major US carriers.

Our team has not personally tested this with Xbox Live, but we have tested a few cellular routers with gaming consoles. In our personal experience, as well as working with customers, we've found NAT types to be rather hit or miss. In most cases, the best NAT type you can get over a cellular Internet connection is a moderate NAT type 2. However, we have seen an Open NAT in some cases. We recommend following the steps on our gaming tip sheet, which can help, and the only other thing that MAY work is to pay the cellular provider for a static IP address. In any case, we can't guarantee what NAT type you'll receive.

Yes, an ethernet switch can be connected to allow more wired connections.